MSP430FR2476TRHBR FRAM Microcontroller IC 16-Bit 16MHz 64.5KB FRAM 32-VQFN (5x5)

MSP430FR2476TRHBR FRAM Microcontroller IC 16-Bit 16MHz 64.5KB (64.5K X 8) FRAM 32-VQFN (5x5)

Description

MSP430FR247x microcontrollers (MCUs) are part of the MSP430™ MCU value line portfolio of ultra-low-power low-cost devices for sensing and measurement applications. MSP430FR247x MCUs integrate a 12-bit SAR ADC and one comparator. The MSP430FR247x MCUs support an extended temperature range from –40°C up to 105°C, so higher temperature industrial applications can benefit from the devices' FRAM data-logging capabilities.

MSP430FR247x MCUs are supported by an extensive hardware and software ecosystem with reference designs and code examples to get your design started quickly. Development kits include the MSP-TS430PT48 48-pin target development board. TI also provides free MSP430Ware™ software, which is available as a component of Code Composer Studio™ IDE desktop and cloud versions withinTI Resource Explorer. MSP430 MCUs are also supported by extensive online collateral, such as our housekeeping example series, MSP Academy training, and online support through the TI E2E™ support forums.

The MSP430 ultra-low-power (ULP) FRAM microcontroller platform combines uniquely embedded FRAM and a holistic ultra-low-power system architecture, allowing system designers to increase performance while lowering energy consumption. FRAM technology combines the low-energy fast writes, flexibility, and endurance of RAM with the nonvolatile behavior of flash.

The TI MSP430 family of low-power microcontrollers consists of devices with different sets of peripherals targeted for various applications. The architecture, combined with extensive low-power modes, is optimized to achieve extended battery life in portable measurement applications. The MCU features a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code efficiency. The digitally controlled oscillator (DCO) allows the MCU to wake up from low-power modes to active mode in less than 10 µs (typical).

Features

• Embedded microcontroller

– 16-bit RISC architecture

– Clock supports frequencies up to 16 MHz

– Wide supply voltage range from 3.6 V down to 1.8 V (minimum supply voltage is restricted by SVS levels, see the SVS specifications)

• Optimized ultra-low-power modes

– Active mode: 135 µA/MHz (typical)

– Standby: LPM3.5, real-time clock (RTC) counter with 32768-Hz crystal: 660 nA (typical)

– Shutdown (LPM4.5): 37 nA without SVS

• Low-power ferroelectric RAM (FRAM)

– Up to 64KB of nonvolatile memory

– Built-in error correction code (ECC)

– Configurable write protection

– Unified memory of program, constants, and storage

– 1015 write cycle endurance

– Radiation resistant and nonmagnetic

• Intelligent digital peripherals

– Four 16-bit timers with three capture/compare registers each (Timer_A3)

– One 16-bit timer with seven capture/compare registers (Timer_B7)

– One 16-bit counter-only RTC

– 16-bit cyclic redundancy check (CRC)

• Enhanced serial communications with support for pin remap feature

– Two eUSCI_A supports UART, IrDA, and SPI

– Two eUSCI_B supports SPI and I2C

• High-performance analog

– One 12-bit analog-to-digital converter (ADC) with up to 12 channels

• Internal shared reference (1.5, 2.0, or 2.5 V)

• Sample-and-hold 200 ksps

– One enhanced comparator (eCOMP)

• Integrated 6-bit DAC as reference voltage

• Programmable hysteresis

• Configurable high-power and low-power modes

• Clock system (CS)

– On-chip 32-kHz RC oscillator (REFO) with 1 µA support

– On-chip 16-MHz digitally controlled oscillator (DCO) with frequency-locked loop (FLL)

• ±1% accuracy with on-chip reference at room temperature

– On-chip very low-frequency 10-kHz oscillator (VLO)

– On-chip high-frequency modulation oscillator (MODOSC)

– External 32-kHz crystal oscillator (LFXT)

– Programmable MCLK prescalar of 1 to 128

– SMCLK derived from MCLK with programmable prescalar of 1, 2, 4, or 8

• General input/output and pin functionality

– 43 I/Os on LQFP-48 package

– 43 interrupt pins on all GPIOs can wake MCU from low-power modes

• Development tools and software

– Development tools

• Target development board MSP‑TS430PT48A

• LaunchPad™ development kit LP‑MSP430FR2476

• Family members (also see Device Comparison)

– MSP430FR2476: 64KB of program FRAM, 512B of information FRAM, 8KB of RAM

– MSP430FR2475: 32KB of program FRAM, 512B of information FRAM, 6KB of RAM

• Package options

– 48-pin: LQFP (PT)

– 40-pin: VQFN (RHA)

– 32-pin: VQFN (RHB)

Applications

• Small form factor industrial sensors

• Low-power medical, health, and fitness

• Battery packs

• EPOS

• Appliances

• Thermostats

• Electric toothbrushes

• PC accessories

Clock Distribution Block Diagram

specification of MSP430FR2476TRHBR

ORIGINAL

Our company ensures that each batch of products comes from the original factory, and can provide original labels and professional testing agency reports.

PRICE

We provide a variety of quotation channels, and sign the order contract after negotiation.

TRANSACTION

After communication and agreement, we will guide you to arrange payment.

DELIVERY CYCLE

Delivery on the same day, generally 5-12 working days, may be slightly delayed during the epidemic, we will follow up the whole process.

TRANSPORT

We will choose the appropriate transportation mode according to your country.

PACKAGING

After communication with you, we will choose the appropriate packaging method according to the weight of the goods to ensure the safe delivery of the goods.

MSP430FR2476TRHBR FRAM Microcontroller IC 16-Bit 16MHz 64.5KB FRAM 32-VQFN (5x5) Images